Koolance CTR-CD12 Manuel d'utilisateur télécharger pdf

The rear of the unit accepts various connections to integrate with your cooling system.

POWER: Connection from

power supply, 12VDC

FAN: Radiator fan con-

nections (2.0A max per

plug, 4.5A total)

TEMP: Temperature sensors

shown on the front display

ATX: Pass-

through lead

for power shut-

down feature

PUMP:

External

pump

INS-FM17/INS-FM16:

Connect an optional flow

meter to display flow rate

ON/SYNC/OFF:

Adjusts LED lighting

of INS-FM16 flow

meter

Power Connection

The temperature sensors and ATX lead

may come pre-connected to your unit.

If not, connect them per the diagram

above.

Connect a 12 Volt 4-pin Molex plug from

the power supply to the power connection

on the rear of the unit.

Fan Connection

This unit has three connections to

power radiator fans. Multiple fans can

be combined into a single plug. (A fan

wiring harness is optionally available from

Koolance).

CAUTION: The total com-

bined amperage of all fans

connected to the unit can not

exceed 4.5A. The maximum

load on a single fan header

is 2.0A.

ATX Pass-Through Lead

The ATX pass-through lead is

responsible for sending the shut-

down signal if any sensor reaches the

preset shutdown temperature (See

Display Panel for configuration).

There is no polarity direction with

the ATX lead. Connect the male ATX

power lead from the cooling unit to

your computer’s main chassis power

button.

Connect the female ATX power lead from

the Slot Adapter to the motherboard’s power

switch connection (often marked “PWRSW”,

“PWSW”, or “PWBT”).

This is the connection that would normally

receive the chassis power button directly.

To Motherboard

Chassis Power

Button

From Cooling

Unit

Flow Meter Connection

The cooling system can show values

for one Koolance INS-FM16, INS-

FM17/N, or INS-FM18 flow meter

(sold separately). The use of a flow

meter is optional.

Connect a flow meter to the

appropriately labeled plug. (Note:

INS-FM18 should connect to the plug

labeled “INS-FM17”.)

CTR-CD12 User Manual v 1.0

Pump Connection

An external 12 Volt DC pump can be

connected to the unit for speed control.

The maximum available amperage is

2.2A.

CAUTION: This product

can be used with a single

12VDC pump with a maxi-

mum amperage of 2.2A.

1 2 3 4

◙ to enable or 4

Résumé du contenu

Page 1

The rear of the unit accepts various connections to integrate with your cooling system.POWER: Connection from power supply, 12VDCFAN: Radiator fan con

Page 2

CAUTION: Generally, sensors report liquid temperature at the water block, which is typically 5-10°C (9-18°F) lower than the actual heat source. This d

Page 3

6The Koolance flow meter model number (SKU) will flash. Press ▼ or ▲ to adjust this based on the following: • INS-FM16: change to “FM-16” • INS-FM17

Page 4 - ◙ to enable or

7Press ▼ or ▲ to change what this line will display among the options described earlier. Press ◙ to move to line 2, and similarly use ▼ or ▲. Press ◙

Commentaires sur ces manuels

Pas de commentaire

Koolance CTR-CD12 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Koolance CTR-CD12. Koolance CTR-CD12 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Koolance CTR-CD12