Koolance VID-NX285N Manuel d'utilisateur
Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Koolance VID-NX285N. Koolance VID-NX285N User Manual Manuel d'utilisatio
- Page / 1
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
All heat sink assembly screws should be removed. There
should be 20 of these on the back of the video card. There are
an additional 2 screws on the rear L-bracket.
Two G1/4 “caps” are included
with the VID coolers which can
be placed opposite the desired
nozzle locations.
NOTE: The video card should be removed from the chassis in order to install this
cooling device. Most cards using the VID-series blocks are disassembled the same
way, although heat sink assemblies of any given model can vary.
CAUTION: Removal of the original heat sink my void your manufac-
turer’s hardware warranty. Please consult the manufacturer if unsure,
and keep all original parts in case of a return/RMA.
!
VID-NX285 Installation Guide v 1.0
1
GeForce GTX 285 Disassembly Screws Back Side (Left) and L-Bracket (Right)
Connecting VID Coolers in SLI or CrossFire
When connecting multiple VID coolers in series, Koolance offers an optional direct-
connect nozzle. This minimizes liquid routing while avoiding potential confl icts with
hardware in between the video cards.
Optional Four Slot Dual Video Connector
(Koolance CNT-VD4)
4
Optional Two Slot Dual Video Connector
(Koolance CNT-VD2)
Optional Three Slot Dual Video Connector
(Koolance CNT-VD3)
Optional Four Slot Dual Video Connector
(Koolance CNT-VD4)
The heat sink and fan can now be carefully
removed. Original thermal paste may present
additional resistance while removing the heat sink.
Unplug the heat sink fan wire. Remove the original
RAM thermal transfer material, and wipe any residual
thermal material from the main GPU chipset.
Koolance VID coolers include redundant
G1/4 threading on both sides. This
means the input/output nozzles can be
placed on either side of the cooler.
Place heat transfer pads on each additional area cooled by
the Koolance liquid block, as determined by the previous
diagram.
3
Place the Koolance block over the video
card.
Using the Koolance-supplied screws and plastic insulating washers, tighten each
screw on the reverse side of the card. There should be 10 of these that correspond
with the water block standoffs.
Koolance-Supplied Screw and
Insulating Washer
Thermal Paste Area
Gray thermal pads have plastic fi lm on both sides that must
be removed before application. White/Pink thermal pads only
have plastic fi lm on one side (white) that must be removed.
Do this after cutting the proper shapes.
Two different sets of heat transfer pads
are included, and each set has a different
thickness. The thermal pad sheet should
be cut into pieces required for your video block contact
areas. Please use the below diagram to determine the
proper sizes.
2
Thermal paste is only required on the main GPU(s). The
other areas will utilize the included heat transfer pads.
Spread thermal compound on the GPU thinly and evenly
using the included paste packet, or a piece of thick paper
(such as a business card). Thermal paste should not be
placed on the surrounding metal support frame or small
surface soldered components.
10 x 10mm
16 x 90mm
15 x 20mm
12 x 60mm
16 x 60mm
90 x 16mm
25 x 55mm
Gray Pad
Pink Pad
10 x 20mm
20 x 10mm
20 x 10mm
1
Résumé du contenu
Page 1
All heat sink assembly screws should be removed. There should be 20 of these on the back of the video card. There are an additional 2 screws on the re
Produits connexes et manuels pour Matériel Koolance VID-NX285N
(1 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.100 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels